Onn Portable Power Hub Quick Start Guide

Check to make sure you have everything below.

1. Portable Power Hub
2. Quick Start Guide
3. 15V 2A adapter

Get to Know Your Portable Power Hub

1. Handle
2. Automobile Auxiliary Power Outlet
3. LCD Display
4. LED Indicator for Powerhub
5. Main Power Button Display
6. Control Button DC Output
7. Ports
8. USB-A Output Ports
9. USB-C Output Port
10. Power Delivery USB-C Port
11. USB Output Control Button
12. LED Indicator for DC Ports
13. DC Output Control Button
14. LED Indicator for USB Ports

1. Ambient Light
2. Ambient Light Button
3. DC Input Port
4. Flashlight Light
5. Flashlight Light Button
6. AC Output Port
7. AC Output Control Button

1. ED Indicator for speaker and Weather Radio
2. Power on / off (Speaker)
3. Volume Down / Previous Track
4. Volume Up / Next Track
5. Bluetooth / Play / Pause
6. NOAA Weather Radio

LCD Display

INPUT: Shows power (watts) amount going into the Portable Power Hub while charging.
OUTPUT: Shows power (watts) amount your devices are using while plugged into the Portable Power Hub.
BATTERY LEVEL: Shows in increments of 10, up to 100 capacity.
When charging your Portable Power Hub you will notice a battery segment blinking, this indicates the current charge status. Once fully charged, all battery segments will be lit and remain white solid.
OVERLOAD WARNING: Power draw exceeds port's maximum allowance, indicator by the button will flash red. You need to remove the device in corresponding port first, and then press the button of the port to reset.
TEMPERATURE WARNING:The unit is over-heating. Disconnect the device, and press main power button again.

Device to Portable Power Hub

Press & hold 10 seconds to activate the Portable Power Hub for INITIAL USE ONLY.

Next time, you can follow below steps to charge your device.

* By automobile auxiliary power outlet

*By AC output port

A output ports" width="" />

*By USB-A output ports

*By DC output ports

TIPS:

1. When any of the control buttons are turned on, even if no devices are being charged, there will still be a certain amount of no-load power consumption. Therefore, it's better to turn off the control buttons after using to avoid draining power.
2. You'll know the output port is turned on when the green LED light by the button is solid.
3. Press the "DISPLAY" button to turn on/off the LCD display.
4. The max power output of the AC port is 200W. If you use the AC port for devices greater than 200W, Power Hub will automatically turns off.
5. When Power Hub has only 1% battery left, the Power Level and Percentage of Capacity Left will flicker to remind you to recharge Power Hub.

Light Mode

Flashlight Mode
Press once to toggle between low brightness, full brightness, SOS, and no brightness mode.

Ambient Light Mode
Press once to toggle between low brightness, medium brightness, high brightness and no brightness.

Charging Your Portable Power Hub

* By DC IN Port

* By Power Delivery USB-C Port

* You can charge your Portable Power Hub with DC IN port and USB-C PD Port at the same time.

Power on / off the Speaker

Press & hold to power on / off the speaker

Bluetooth® Connection

In Bluetooth mode, activate the Bluetooth function on your device and search Bluetooth devices, then select "onn. POWERHOUSE" to start connecting.

NOAA Weather Radio

Press once WB button to search for Weather Band, the LED indicator will be solid green. The radio will find the strongest signal Weather Band channel from the local radio.
Press & hold WB button to activate or exit auto-wake-up mode. The LED indicator will flash slowly, and you will receive every advisory, watch and warning automatically once activated.
Weather Band: 162.400~162.550MHz

Hints and Tips

Portable Power Hub will automatically turns off when the power of the device exceeds the rated output power (200W). The LCD display will alert when the power system detects that the device being used is shorted or overloaded. Please confirm whether the device parameter specifications meet the scope of the Portable Power Hub before using it.

How to clear the automatic protection after it is activated?

1. If the OVERLOAD mark is lit on LCD display
   1. Disconnect the device.
   2. Press once the main power button to clear the automatic protection.
   1. Disconnect the device.
   2. Charge the Portable Power Hub for 2~3 minutes.
   3. Press once the main power button to clear the automatic protection.

   To preserve battery lifespan, use and recharge at least once every 3 months.

   

   We'd love to hear from you. Scan with your Walmart app and let us know what you think.
   
   Need help? We're here for you every day 7 a.m. – 9 p.m. CST.
   1-888-516-2630 Give us a call!

   

   Documents / Resources

   Download manual

   Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

   Need Assistance?

   Do you have a question about the Portable Power Hub that isn't answered in the manual? Leave your question here.

   Thank you! Your question has been received!